Water Tank Monitoring
Monitor your water tanks from your phone. Pay by Zelle or Bank transfer or Monero (XMR) — no credit cards. Ships from Hawaii.
Combo Plug-in With WiFi & Tank Sensor
The easiest install when your tank is near power. The package includes 1 Combo Gateway with a tank sensor and Antenna and private website access. One board connects to your Wi-Fi and reads your tank directly. It is powered by a plain USB-C cable from any USB charger, so there is no battery or solar panel to deal with.
Your private website dashboard is included at no extra cost:
• Live tank levels, water usage and connected status
• Email alerts based on water level: getting low, critically low and full
- Fully Assemble Unit
- 1 Control Box with hardware
- 1 Antenna
- 1 Water Tank Sensor
- Remote Water Pump Shut Off and On or Automatic plus more... This can really give you control of your system from your laptop Phone Anywhere in the World. This does require the purchased Add on Pump Relay
- Private website access
How it works
2. Connect it to your Wi-Fi.
3. Connect the tank sensor.
4. Add it to your account with its pairing code, then set your tank size and low-water levels on the dashboard.
Combo Solar With WiFi & Tank Sensor
For a tank with no outlet nearby. The package includes 1 solar-powered Combo Gateway with a tank sensor and private website access. Solar panel inter-graded into the Control Box charge rechargeable battery already wired together, so there is nothing to change or replace. It needs Wi-Fi within range of the tank.
Your private website dashboard is included at no extra cost:
• Live tank levels, water usage and connected status
• Email alerts based on water level: getting low, critically low and full
- 1 solar-powered Combo Gateway with tank sensor (panel, charge controller and battery already wired together)
- Private website access
How it works
2. Connect it to your Wi-Fi.
3. Connect the tank sensor.
4. Add it to your account with its pairing code, then set your tank size and low-water levels on the dashboard.
Remote Tank Starter
Everything you need to watch one water tank from anywhere. The package includes 1 Tank Transmitter, 1 House Gateway and private website access.
The Tank Transmitter is solar powered, with its panel, charge controller and battery already wired together, so there is nothing to charge or replace. The House Gateway plugs in indoors and connects to your Wi-Fi.
Your private website dashboard is included at no extra cost:
• Live tank levels, water usage and connected status
• Email alerts based on water level: getting low, critically low and full
How it works
2. Mount the Tank Transmitter at your tank with its solar panel in the sun.
3. Add both to your account with their pairing codes.
4. Set your tank size and low-water levels on the dashboard.
Need more range? Add a Bridge Repeater.
Tank Transmitter With Solar & Tank Sensor
The Tank Transmitter sits at your water tank, measures the water level and sends it wirelessly to your House Gateway. It is fully solar powered: a solar panel, a built-in solar charge controller and a rechargeable internal battery come wired together, so there are no batteries to take out, charge or replace. The dashboard shows each transmitter's battery level. Every account has its own private key, so your tanks only talk to your gateway.
How it works
2. Connect the level sensor to the transmitter at your tank.
3. Add it to your account with its pairing code. The dashboard gives each tank its own number.
4. Set the tank depth and size on the dashboard so the level shows in percent and gallons, and set your low and critical warning levels.
It needs to be within wireless range of a House Gateway. For a long distance, add a Bridge Repeater.
Pump Relay Add-On With Unlock
This is an add-on purchase. It is the relay that lets you control your water pump from your dashboard, and buying it also permanently unlocks pump control on your account.
You choose the level where the pump stops and the level where it is allowed to run again, and you can press Emergency stop and Resume right on the tank's card on your dashboard.
Pump size: This relay is rated for 120 volt pumps up to 5 amps when wired directly. If your pump is 120 volt and draws more than 5 amps, you will need a contactor. If your pump is 220 to 240 volt, you will need a 2-pole contactor with a 120 volt coil, rated for your pump.
How the contactor is used: The bottom of our control box has two labeled wire connectors for this purpose, HOT IN and SWITCHED OUT. The box itself is never opened. The contactor is mounted in its own separate enclosure, outside the control box. Connect a 120 volt hot wire from a nearby source to the HOT IN connector. Connect the SWITCHED OUT connector to one of the contactor's coil terminals. Connect the 120 volt neutral wire from the same source straight to the other coil terminal. The wires that used to run from your 240 volt breaker to your pump (or to its pressure switch) connect to the contactor's L1 and L2 terminals. New wires from T1 and T2 go to where those original wires connected, and your pressure switch stays where it is. When the relay closes, the pump can run. When the relay opens, or power is lost, the pump stops.
- 1 Pump Relay
- Permanent pump control on your dashboard account
How it works
2. On your dashboard, switch on "This tank has a pump" for that tank.
3. Set the level where the pump stops and the level where it runs again.
4. Use Emergency stop and Resume pump on the tank's card any time.
House Gateway (Inside Home)
The House Gateway sits indoors, plugs into any USB power adapter and connects to your Wi-Fi. It listens for your tank transmitters over a long-range wireless link and sends every reading securely to your private online dashboard, so you can check your water levels from anywhere. It is the first piece you set up, and it is what links your tanks to your account.
How it works
2. Add it to your account on the dashboard with its pairing code.
3. Your tank transmitters then report to it wirelessly, and their levels appear on your dashboard.
The dashboard shows a clear Connected or Not connected status for the gateway.
Long-Range Pro
For properties where the tank is too far from the house. The package includes 1 Tank Transmitter, 1 House Gateway, 1 Bridge Repeater and private website access.
The Tank Transmitter and Bridge Repeater are both solar powered, so neither needs an outlet, Wi-Fi or battery changes. The repeater carries your tank's readings to the gateway.
Your private website dashboard is included at no extra cost:
• Live tank levels, water usage and connected status
• Email alerts based on water level: getting low, critically low and full
- 1 Tank Transmitter, solar powered
- 1 House Gateway (plugs into any USB power adapter)
- 1 Bridge Repeater, solar powered
- Private website access
How it works
2. Mount the Tank Transmitter at your tank.
3. Place the Bridge Repeater about halfway between the tank and the house, with its solar panel in the sun.
4. Add all three to your account with their pairing codes.
Multi-Tank
Watch two tanks on one dashboard. The package includes 2 Tank Transmitters, 1 House Gateway and private website access.
Both transmitters are solar powered with nothing to charge or replace, and each tank gets its own level, warnings and water-usage page.
Your private website dashboard is included at no extra cost:
• Live tank levels, water usage and connected status
• Email alerts based on water level: getting low, critically low and full
- 2 Tank Transmitters, solar powered
- 1 House Gateway (plugs into any USB power adapter)
- Private website access
How it works
2. Mount each Tank Transmitter at its tank with its solar panel in the sun.
3. Add all three to your account with their pairing codes.
4. Set the size and low-water levels for each tank.
Solar Bridge Repeater
The Bridge Repeater picks up the readings from your tank transmitters and passes them on, so a tank that is too far from the House Gateway can still report. Like the transmitter it is fully solar powered, with a solar panel, built-in solar charge controller and rechargeable internal battery wired together, so it needs no outlet, no Wi-Fi and no battery changes. It checks in with your account regularly, and the dashboard shows whether it is Connected.
How it works
2. Add it to your account with its pairing code.
3. The dashboard shows the repeater as Connected once it has been heard by your gateway.
A repeater only passes your tanks' readings along. It has no tank of its own.